On this page
- Remote Or Opener? Start With The Wall Button
- Eight Common Reasons A Garage Remote Stops Working
- How To Reprogram A Garage Remote By Brand
- Lost Or Stolen Remote? Erase It First
- When The Remote Isn’t The Problem
- What We Check When We Come Out
- Frequently Asked Questions
- Still Stuck In The Driveway? We’ll Get You Back In
It’s a 39-degree arvo in January. There’s ice cream going soft in the boot, two hot kids in the back seat and a garage door that won’t open. You press the remote again, then hold it down, then aim it at the door like you’re changing the TV channel. The door stays shut.
A garage remote that stops working usually has a flat battery, a locked wall control, interference near the opener or a code that’s dropped out of the opener’s memory. If you can reach the wall button inside, press it. If the door moves, the remote or its signal is at fault. If it doesn’t, check the power and the opener.
Most of the time, you’ll have it sorted before the ice cream melts. Work through these in order:
- Press the wall button inside the garage.
- Fit a fresh battery and wipe the contacts.
- Turn off the lock or vacation setting on the wall control.
- Try your spare remote, if you have one.
- Check that the antenna wire hangs straight down from the motor.
- Switch off nearby LED globes, routers and chargers, then try again.
- Reprogram the remote using the steps for your brand below.
Remote Or Opener? Start With The Wall Button
The wall button splits the system in two, which is why it’s the first thing our technicians press when they arrive.
- The wall button works but the remote doesn’t: the opener’s fine, so the fault is in the remote, its battery, its programming or the signal.
- Neither works: check the power point, the opener’s plug and the meter box for a tripped breaker. If the power’s on, the opener itself needs attention.
- Both remotes stopped on the same day: it’s rarely the remotes. Look at the lock setting, interference and the opener’s receiver.
- You can hear the opener, but the door won’t move: someone may have pulled the manual release, usually a cord with a red handle hanging from the opener, or a spring may have broken. If the door suddenly feels like it weighs a tonne, stop there. A broken spring needs a technician, and forcing the door can hurt you or wreck the opener.
Eight Common Reasons A Garage Remote Stops Working
Work down this list in order. The first three account for most of the remote call-outs we get.
1. A Flat Or Badly Seated Battery
Many handheld remotes run on a CR2032 coin cell, though some older ones take a CR2016 or a small 12-volt A23. A dying battery can still make the LED glow while sending a signal too weak to reach the opener, so the light proves nothing. Perth summers make it worse, because a remote left on the dashboard through a run of 40-degree days drains faster than one kept indoors. Most servos sell coin cells. B&D says its remote batteries typically last 12 to 24 months, and a battery swap won’t erase the programming.
2. The Wall Control Is Locked
Many wall controls have a lock or vacation button that blocks every remote while the wall button keeps working. It’s easy to switch on by accident, whether you brush past it with a bike or the kids are mucking around with the buttons. Press or hold the lock button again to switch it off, then try the remote. The method varies by brand, so check the label on the wall control or your manual.
3. Interference Near The Opener
Remotes talk to the opener by radio, mostly on the 433MHz band in Australia, and nearby electronics can swamp that signal with noise. Cheap LED globes in the opener’s light, Wi-Fi routers and phone chargers can all do it. So can a solar inverter, and with so many Perth roofs carrying panels, the inverter often ends up on the garage wall. Switch these off one at a time and try the remote after each. If it suddenly works, you’ve found the cause.
4. A Blocked Or Damaged Antenna
Most openers have a thin antenna wire hanging from the motor. If it’s been tucked up, cut short or pinned against the metal rail, the remote may only work when you’re standing underneath. Let it hang straight down and clear of metal. A remote that used to open the door from the street but now needs to be a metre from the motor has a range problem, not a programming one.
5. The Code Has Dropped Out Of The Opener’s Memory
A power surge when a winter front rolls in off the Indian Ocean, a reset of the opener or someone holding the learn button too long while adding a new remote can all wipe stored remotes. If the battery’s fine and the lock is off, reprogramming usually gets it going again.
6. The Remote Is Worn Or Damaged
Remotes get dropped, sat on, chewed by the dog and left out in the rain. Worn contacts, a cracked case or water damage can kill one even with a fresh battery. If your other remote works and this one still doesn’t after a new battery and reprogramming, replace it. Wall-mounted remotes wear out too: on a job in Ellenbrook, the wall remote had started responding only some of the time, so we supplied and programmed a new Centurion-compatible one. The same visit turned up three damaged plastic hinges and worn lift cables, which explained why the door had started catching as it moved.
7. The Remote Doesn’t Match The Opener
Remotes aren’t universal, even within one brand. B&D’s current Tri-Tran+ remotes don’t work with older DIP switch openers, and Merlin’s remotes are split between its Security+ 2.0 and older Security+ code systems. Read the model number off the opener’s label before you buy, and be wary of cheap universal remotes sold online. Our range of replacement garage door remotes covers the brands we service.
8. A Fault In The Opener Or Receiver
If the wall button works but no remote will pair, the opener’s receiver may have failed. Age and lightning surges both damage receivers, and so does salt air near the coast, from Quinns Rocks down to Rockingham. A technician can test the receiver and replace the board or the opener as part of our garage door motor repairs.
How To Reprogram A Garage Remote By Brand
Reprogramming takes a few minutes and a ladder. Close the door, keep the doorway clear and climb down before you test, and check your manual if the buttons on your opener look different. If the code doesn’t take on the first go, don’t stress: nothing’s broken. Give it a minute and start again from the top. Just don’t hold a learn or code button longer than the steps say, because on many openers a long press erases every remote.
Merlin
On current Merlin openers the learn button is yellow, and you’ll usually find it under the light cover or on a side panel. Press and release it once, and within 30 seconds hold down the remote button until the opener’s light blinks or the motor clicks. Release it and test. Four-button remotes on older openers use a different sequence, which you’ll find in our guide to program a Merlin garage remote.
B&D
B&D roller door openers keep their programming buttons behind a clear cover at the front of the motor. Take it off, hold CODE SET for two seconds, then let go. Hold the remote button for three seconds, release it and hold it for another three seconds. Refit the cover and test. On B&D sectional openers, the buttons are at the back: keep pressing MODE until the opener’s remote light comes on, then hold CLOSE while you press the remote button for three seconds, twice. Let go of CLOSE and press MODE once more to finish.
Steel-Line
On Steel-Line SD series openers, press the P and + buttons together until LED 7 flashes. Press +, press the remote button twice, then press P to save.
ATA
On ATA SecuraLift openers, press and hold the Door Code button. While you hold it, press the remote button for two seconds, pause for two seconds and press it again for two seconds. Release Door Code and test.
Got another brand? The learn button method that many openers share is covered in the garage door remote programming guide on our blog.
Lost Or Stolen Remote? Erase It First
Losing a remote is unsettling, because anyone who finds it holds a working key to your garage, and to your house too if the internal door isn’t locked. A new remote won’t lock the old one out: it stays active until it’s wiped from the opener. Clear every stored code, then pair the remotes you still have, one at a time. If it was taken from your car, report it to WA Police too. Do the same wipe when you move house, since there’s no telling how many remotes the previous owners handed out. We’ve set out the steps to re-code your garage opener in detail.
When The Remote Isn’t The Problem
Sometimes the remote’s fine and the door still misbehaves.
- The door reverses just before it reaches the floor: that’s usually the safety beams or something in the door’s path. If it opens with nobody near a remote, read about what causes a garage door opening by itself.
- The motor is beeping or flashing: the opener is reporting a fault, such as a flat backup battery or a blocked beam. The common beep and flash patterns are decoded in our post on garage door motor beeping.
What We Check When We Come Out
Tyler Gefterman, who owns Slide & Glide, has been fixing and fitting garage doors for more than 12 years. Between them, our installers have more than 20 years in the trade. On a remote call-out, we start with the batteries, the lock setting and the antenna, which often solve it within minutes. Then we test the wall control and the receiver, and re-code every remote that should be on the system, so you know exactly which handsets can open your door. We keep spare remotes, sensors and opener parts in our vans, so a lot of remote faults are fixed before we leave.
Not every call-out is the remote. A Willetton homeowner called us because the door had stopped working reliably, and testing showed the motor was failing. We replaced it with a Jaytech 1200N for $1,000, programmed a new Jaytech remote and ran the door through several cycles to check the limits and safety settings.
Frequently Asked Questions
Perth homeowners ask us these remote questions more than any others.
Why Did Both My Garage Remotes Stop Working At Once?
When every remote fails at the same time, the cause is usually at the opener: the wall control’s lock setting, a power problem, interference or a faulty receiver. Check the lock and the power first. If the wall button works and both remotes still fail, have the receiver tested.
Why Isn’t My Remote Working After I Changed The Battery?
Check it’s the right type, sits the right way up and has clean contacts. A battery change rarely erases the programming, so if it still won’t work, reprogram it, then rule out interference and the lock.
Why Does My Remote Only Work When I’m Close To The Door?
Short range points to a weak battery, a tucked or damaged antenna on the motor or interference from nearby LED globes and electronics. Sort out those three and most remotes work from the street again.
Does A Power Outage Reset Garage Remotes?
Usually not, but a surge during a storm can scramble an opener’s memory or damage its receiver. If the remotes stopped after a blackout but the wall button works, try reprogramming one. If it won’t pair, the receiver may need repair.
How Much Does A Replacement Garage Remote Cost?
It depends on the brand and model. As a guide, supplying and programming a new Jaytech remote cost $79 on a job in Willetton, and programming a new wall remote in Ellenbrook was $65 plus GST.
Can I Use A Universal Remote On My Garage Door?
Sometimes. A universal remote has to support your opener’s frequency and code system, and many rolling code openers only accept their own brand. Send us the model number from the motor’s label and we’ll tell you which remote suits it.
Still Stuck In The Driveway? We’ll Get You Back In
Back to that hot driveway. Usually it’s a fresh coin cell, a lock button switched off or a quick re-code, and the door rolls up on the first press with the ice cream still frozen. If the button still does nothing after all that, the receiver or the opener is the likely cause, and that’s a job for a technician.
Our technicians work out of Osborne Park and cover homes from Joondalup to Mandurah, and we belong to the Australian Garage Door Association. Ring 0489 266 468 and you’ll speak to someone on our Perth team, 24/7 if you’re locked out with the car inside. Or send us a booking request, and you’ll hear from us within 2 hours.
On this page
- Remote Or Opener? Start With The Wall Button
- Eight Common Reasons A Garage Remote Stops Working
- How To Reprogram A Garage Remote By Brand
- Lost Or Stolen Remote? Erase It First
- When The Remote Isn’t The Problem
- What We Check When We Come Out
- Frequently Asked Questions
- Still Stuck In The Driveway? We’ll Get You Back In
